Midea One way Cassette Fan Coil Unit Eurovent Certified One Way Cassette FCU 153mm Deep Body 7 Speeds 14W Draw 30 Saving

Corridor and perimeter zones are usually the first systems a design team fixes and the last to receive detailed attention, which is why a terminal unit that can be specified from verified data saves weeks of coordination. The Midea One-way Cassette Fan Coil Unit is a 153mm-deep chassis with single-direction discharge, sized for the narrow ceiling voids above corridors, lift lobbies, entry foyers and retail perimeters where a four-way cassette cannot be accommodated. Across the combined AC and DC range the unit covers 300–600 CFM and 2.65–5.20 kW of cooling, so one schedule line replaces several one-off selections, and the Eurovent-certified performance figures allow the unit to be written into a performance specification without inviting an equivalent-product argument at tender.

Hydraulically the unit integrates without special provisions: G1/2" coil connections, a 1.6 MPa maximum working pressure that sits comfortably inside normal closed-loop chilled and low-temperature hot water practice, a two-row coil, and 220–240V / 1Ph / 50Hz single-phase supply drawing 32–40W on AC models and 14–38W on DC. The 750mm condensate lift pump is factory-fitted rather than a schedule item, which removes gravity fall from the ceiling void design and takes away the most common cause of water staining on newly finished ceilings. AC and DC variants share the same body dimensions, the same pipe positions and the same pump, so a late motor-tier decision never disturbs coordinated drawings.

The motor tier is the one genuine design decision. AC models offer proven three-speed control at the lowest capital cost; the DC brushless version provides seven speeds through the KJR-75A wired controller, a minimum draw of 14W, fan energy reduced by up to 30% and sound pressure 2–5 dB(A) lower than the AC equivalent — figures that support an energy or acoustic clause in the specification rather than an aspiration. Where a project demands non-standard voltage, protocol or branding, Hongtai supports OEM/ODM supply with custom voltages from 180–440V at 50/60Hz, Modbus RTU and BACnet, so the schedule can name the local grid and the building protocol without a derogation.

• 153mm Depth, Documented — Clears the shallow voids above corridors and lobbies where four-way cassettes cannot be scheduled; a fixed, quotable dimension for ceiling-zone coordination.
• Eurovent-Verified Capacity Band — 300–600 CFM and 2.65–5.20 kW published as third-party verified data, so the unit is specified by performance rather than by model reference.
• 750mm Lift Pump as Standard — Removes gravity fall from the ceiling void design and takes a line off the condensate drainage schedule.
• 1.6 MPa Maximum Working Pressure — Compatible with standard closed-loop chilled and low-temperature hot water systems without a pressure-reducing interface.
• G1/2" Connections on Both Tiers — Hydraulic design is unchanged when the motor tier changes; no re-coordination of pipe sizes or valve sets.
• Single-Phase Standard Supply — 220–240V / 1Ph / 50Hz with 32–40W (AC) or 14–38W (DC) input simplifies circuit and panel allocation.
• Seven-Speed DC with KJR-75A — Verified 14W minimum draw, up to 30% fan energy saving and 2–5 dB(A) lower sound for energy and acoustic clauses.
• OEM/ODM Compliance Support via Hongtai — Custom voltage 180–440V at 50/60Hz, Modbus RTU and BACnet for specifications written around local grid and BMS standards.

Where the specification is silent on fan energy, the AC three-speed version satisfies the duty at the lowest capital cost and with a control philosophy every operator already understands. Where the specification carries an energy or acoustic performance clause, the DC brushless version is the defensible selection: seven speeds for commissioning balance, 14W at minimum speed, up to 30% lower fan energy and 2–5 dB(A) lower sound pressure — all achieved without changing the 153mm body, the 750mm pump or the G1/2" connections. Because the two tiers are dimensionally identical, the motor decision can be deferred to tender stage without reissuing coordinated ceiling and hydraulic drawings.

1. Hotel Corridor Design — The slim chassis allows a continuous corridor ceiling zone without dropping the bulkhead; the DC tier supports guestroom acoustic criteria.
2. Office Circulation and Lift Lobbies — Directional discharge matches the load profile of transit zones, avoiding over-sized terminal units on the schedule.
3. Residential Common Areas — Preserves structural ceiling height in apartment foyers and lift approaches.
4. Retail Perimeter Zones — Single-direction throw follows shopfront geometry and removes dead spots along glazing.
5. Healthcare Circulation Routes — Low sound pressure and tool-free filter access align with estates maintenance and infection-control procedures.

• CE Marking — European conformity for safety and electromagnetic compatibility.
• Eurovent Certified Performance — Third-party verified capacity and efficiency ratings.
• ERP Compliant — Meets EU Energy-related Products Directive requirements.
• RoHS Compliant — Restriction of Hazardous Substances directive conformance.
• GB/T 19232 — Chinese national standard for fan coil unit performance testing.

• Eurovent certified fan coil unit
• one way cassette FCU specification
• fan coil unit selection guide
• fan coil 1.6 MPa working pressure
• Modbus BACnet fan coil unit
• 153mm slim cassette FCU datasheet
• DC brushless cassette FCU specification
• fan coil schedule specification clause